Pendulum Impact Tester

Leading Manufacturers, Exporters and Wholesaler of Pendulum Impact Tester ( Model - IT ASTM ), Pendulum Impact Tester (Model - IT 30 ) and Pendulum Impact Tester (Model - IT30(D) ) from Kolhapur.

Business Type Manufacturer, Exporter, Supplier
Model IT 30
Maximum Capacity 300 J/168 J
Max. Scale Graduation 0.5 J
Overall size (Approx.) 1.1m x 0.45m x 1.65m (H)
Net Weight (Approx.) 375 kg.

Preferred Buyer From

Location Worldwide

MODEL : IT ASTM

The Impact Tester offered with 300 & 400 J energy exclusively for Charpy test confirming to ASTM E-23. This machine is geometrically checked in the works to the more stringent requirements of the American standard. The accuracy of the machine is then verified by PROOF TEST by testing standard test specimens supplied by the NIST, USA. Two sets (Low & high energy-1 Set (4 Nos.) each.) must agree with the normal values within certain tolerance specified.

 

Standard Accessories

  • Charpy Striker 
  • Anvil 
  • Spanner Set 
  • Manual
Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Model IT 30
Maximum Capacity 300 J/168 J
Max. Scale Graduation 0.5 J
Overall size (Approx.) 1.1m x 0.45m x 1.65m (H)
Net Weight (Approx.) 375 kg.

Preferred Buyer From

Location Worldwide

The pendulum Impact Tester, Model IT-30 is designed for conducting Izod, Charpy test. The test methods confirm to BS:131:PART 4-1972

 

(Amended 15 Aug. 1993) BSEN:10045-2:1993.

The pendulum is mounted on antifriction bearings. It has two starting positions, the upper one for Charpy the lower one for Izod testing. On release, the pendulum swings down to break the specimen & the energy absorbed in doing so is measured as the difference between the height of drop before rupture of the test specimen and is read from the maximum pointer position on the dial scale.

 

(It is read on digital readout in case of electronic machines).

There are two strikers and one combined support anvil available for fitting in to the pendulum and on the base of machine for the Izod, Charpy test respectively. Changing from one striker to another is achieved simply by fixing the new striker into it’s position.

 

CHARPY TEST

The Charpy test piece rests on alloy steel support anvils, fitted on the base of the machine rigidly held in position by Allen screws. End stopper is provided for quickly and accurately locating the test piece centrally between the supports. 

 

IZOD TEST

The Izod Test piece is clamped vertically in Izod support fitted on the base of the machine. The support is provided with a machined vertical groove to suit the test piece size. The front clamp piece and the Allen screw enable clamping of the test piece in correct height with the help of Izod setting gauge supplied.

 

Optional accessories

  • Self centering tong for quick and accurate setting of Charpy test specimen
  • ‘V’ notch milling cutter.
  • Caliper gauge checking V notch for Izod & Charpy. 
  • ‘U’ notch milling cutter.
  • Templates for checking 10x10mm. Cross section of Izod/Charpy test specimen.
  • Depth notch gauge including V & U notch gauges for checking depth below V/U notch, angle and radius.

 

Standard Accessories

  • Izod Striker 
  • Charpy Striker 
  • Anvil 
  • Spanner Set
  • Manual
Read More...


Yes! I am interested


Business Type Manufacturer, Exporter, Supplier
Model IT 30 (D)
Maximum Capacity 300 J/170 J
Max. Scale Graduation 2 J
Overall size (Approx.) 1.32m x 0.45m x 1.05 m (H)
Net Weight (Approx.) 375 kg.

Preferred Buyer From

Location Worldwide

The pendulum Impact Tester, Model IT-30 is designed for conducting Izod, Charpy test. The test methods confirm to BS:131:PART 4-1972

 

(Amended 15 Aug. 1993) BSEN:10045-2:1993.

The pendulum is mounted on antifriction bearings. It has two starting positions, the upper one for Charpy the lower one for Izod testing. On release, the pendulum swings down to break the specimen & the energy absorbed in doing so is measured as the difference between the height of drop before rupture of the test specimen and is read from the maximum pointer position on the dial scale.

 

(It is read on digital readout in case of electronic machines).

There are two strikers and one combined support anvil available for fitting in to the pendulum and on the base of machine for the Izod, Charpy test respectively. Changing from one striker to another is achieved simply by fixing the new striker into it’s position.

 

CHARPY TEST

The Charpy test piece rests on alloy steel support anvils, fitted on the base of the machine rigidly held in position by Allen screws. End stopper is provided for quickly and accurately locating the test piece centrally between the supports. 

 

IZOD TEST

The Izod Test piece is clamped vertically in Izod support fitted on the base of the machine. The support is provided with a machined vertical groove to suit the test piece size. The front clamp piece and the Allen screw enable clamping of the test piece in correct height with the help of Izod setting gauge supplied.

 

Optional accessories

  • Self centering tong for quick and accurate setting of Charpy test specimen
  • ‘V’ notch milling cutter.
  • Caliper gauge checking V notch for Izod & Charpy. 
  • ‘U’ notch milling cutter.
  • Templates for checking 10x10mm. Cross section of Izod/Charpy test specimen.
  • Depth notch gauge including V & U notch gauges for checking depth below V/U notch, angle and radius.

 

Standard Accessories

  • Izod Striker 
  • Charpy Striker 
  • Anvil 
  • Spanner Set
  • Manual
Read More...


Yes! I am interested



Looking for Product Name ?

Close

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us